XNX Universal Transmitter 2022

0

XNX Universal Transmitter

XNX is a versatile, universal transmitter that features a single power source and three relays. Its programmable features allow you to choose between Source, Sink, or Isolated modes. Regardless of the mode you choose, XNX can handle the job.

XNX is a highly flexible, universal gas transmitter

The XNX is a universal gas transmitter with a modular design that supports a wide range of sensor technologies. This versatile transmitter is approved to meet ATEX and CSA standards. It also offers flexibility in the way signal outputs are configured and is easy to install and maintain. It is ideal for many industries, including offshore oil and gas exploration, refineries, gas transmission, and power stations.

Its powerful advanced communications module, which comes with HART and EDDL software, enhances efficiency and flexibility. The XNX offers a variety of signal outputs and configuration options, including Modbus, Foundation Fieldbus, and relays.

It uses magnetic switches to enable nonintrusive operation

XNX duct-mount transmitters use magnetic switches to enable nonintrusive operation. The magnetic switches are activated by using a magnetic end of a screwdriver. These transmitters have a minimum of three parts: the transmitter, sensor, and duct-mount kit.

The XNX transmitter uses three different relays: Relays 1 and 2 for alarm level detection, and a third relay for faults and special states. Honeywell Analytics recommends that you use the fault relay in all installations, as it is normally energized and will open if the power fails. The XNX transmitter has an optional Modbus interface, which allows the transmission of local user interface functions.

It has three relays

The XNX universal transmitter has three relays to enable you to control different aspects of your wireless system. The first relay controls alarm level 1 and the second relay controls alarm level 2, while the third relay controls faults and special states. The fault relay is recommended by Honeywell Analytics for all installations and is normally energized, but will open in the event of a power failure. The XNX transmitter is also equipped with an optional Modbus interface to enable transmission of local user interface functions.

The XNX transmitter supports HART over 4-20mA as its standard communications protocol. It also supports Modbus and Foundation Fieldbus. It has been registered with the HART Communication Foundation. It is also UL and INMETRO-listed and has been certified for use with the U.S. and Brazilian standards. It also has a receptacle for mounting on a two to six-inch pipe, and comes with two carriage bolts, lock washers, and a pipe mount bracket.

It uses a single power source

The XNX universal transmitter uses a single power source to provide power to multiple transmitters. The transmitter’s EC and mV versions operate on 16 to 32 VDC, while the generic 4-20 mA output version operates on 18 to 32 VDC. The transmitter’s performance is affected by high inrush loads, so use a resistive load for best performance. In addition, the distance to which the transmitter can be installed depends on its power source. The 4-20 mA output signal can easily handle the distance back to the control equipment.

The XNX universal transmitter supports multiple sensor types. It also offers different sensor cover styles. Each sensor type requires a specific personality, which determines the transmitter’s behavior.

It uses a common interface

A universal transmitter uses a common interface for communicating with other hardware devices. This interface allows the receiver and transmitter to communicate without synchronizing signals. This type of interface is very flexible and configurable, and is ideal for applications that require high-speed data transfer. However, the advantages and disadvantages of this type of interface are not well-defined.

A common interface is a standard for data communications equipment. Traditionally, data communications referred to the exchange of digital data between a mainframe computer and a remote computer terminal. However, the term “data communications” can also refer to analog data communication between two devices. Traditionally, this type of communication would have used a voice line or a modem.

It uses a common spare part

The XNX Universal Transmitter is an electronic sensor that can interface with a variety of products. It has the ability to output 4-20 mA current and can be configured for Sink, Source, or Isolated operation. The XNX Universal Transmitter uses a common spare part to facilitate wiring.

The XNX Universal Transmitter is an ideal solution for single-person or small engineering teams. Its common interface and spare parts ensure ease of use and minimises the amount of labour required for installation and maintenance. Users can also change the operation and settings of the transmitter without having to open it. This single-person operation is made possible by the XNX’s IS HART terminal port and local LEDs that give an indication of the current status.

 

Leave A Reply

Your email address will not be published.